Magnetic Field Analysis of Disk Coreless Permanent Magnet Synchronous Motor Based on Thickness Variation Halbach Array

Being a new permanent magnets(PMs) arrangement, the Halbach array could approve the magnetic flux density effectively, through weakening the magnetic flux density in one side of the PMs array, meanwhile strengthening the magnetic flux density in the other side. In the disk coreless PM synchronous motor (PMSM), the magnetic flux density is required to be sine wave and the peak value should be as high as possible. The paper deals with the application of the 90° Halbach array in the disk coreless PMSM, adopting NdFeB PMs. For the thickness of PMs influences the magnetic flux density in the air gap, the thickness variation technology is adopted. Through altering the adjacent PMs thickness, nine different PMs thickness combination is analyzed by FEM methods. And the conclusion is that when the thickness of tangential magnetization PMs is great than that of the radial magnetization PMs, the magnetic flux density wave is closer to sine wave than when the thickness of the tangential magnetization PMs is smaller than that of the radial magnetization PMs. Furthermore, when the thickness of the tangential magnetization PMs is great than that of the radial magnetization PMs, keeping the thickness of the tangential magnetization PMs being 0.006 m and the thickness of the radial magnetization PMs variation from 0.0048 m to 0.006 m, the magnetic flux density in the air gap will become closer to sine wave gradually, and then it becomes nonsinusoidal again. And when the thickness of radial magnetization PMs is 0.0054 m and 0.0055 m, the waves of magnetic flux density in the air gap are better than others.     

浸入式水口MgAlON质内衬材料的抗Al2O3附着性研究

浸入式水口在连铸过程中，特别是多炉连铸铝镇静钢时，由于Al2O3在水口内壁附着引起堵塞问题。研究了无碳无二氧化硅的MgAlON质耐火材料，考察了MgAlON—Al2TiO5、MgAlON—BN、Al2O3-C、CaO-ZrO2-C材料的抗Al2O3附着性。结果表明，MgAlON-AT复合材料的抗舢203附着性和抗钢水侵蚀性均优于其它材料．     

Study on Oxygen-Sensing Properties of LaNiO3 Thin Films

The synthesis of rare-earth perovskite-type composition thin films of LaNiO₃ by means of the inorganic-sol-gel (ISG) method was studied. The structural stability under high temperature in reducing atmospheres and the oxygen-sensitivity mechanism of the LaNiO₃ thin films were examined. It is shown that under the experimental conditions, LaNiO₃ decomposes and the valance states of nickel are +2 and +3.     

一种高效的图像细化算法在焊缝跟踪中的应用

针对焊缝跟踪图像处理的特点，研究了二值化后的图像如何进一步细化的方法；采用先对焊缝的边缘进行提取，然后从垂直于焊缝的方向进行扫描的方法，取两条边缘的中点，即是焊缝的骨架；结果表明：此算法能准确地对一幅二值图细化，满足焊缝跟踪中图像处理的要求；这种算法的突出特点是计算量小，处理速度快，非常适合于焊缝的实时处理跟踪，而且不用改写算法，既适合于黑色背景白色图像，也适合于白色背景黑色图像.本算法通过推导得到四条处理准则，在遵循这几条处理准则的基础上逐点扫描图像，按照准则来确定目标点的删除与保留，达到细化的最终目的.     

Improved Repeatability of Pulsed Field Magnetometry Measurements Through Peltier Effect Temperature Control of Measurement Coils

Pulsed Field Magnetometers (PFMs) offer a method for high speed full loop characterisation of hard magnetic materials. As there is no dependency on iron to close a circuit, the repeatability of the technique is good. By utilising Peltier effect techniques to control the temperature of the measurement coil systems employed in a Pulsed Field Magnetometer, the level of repeatability of measurements can be significantly improved.     

Effect of Thickness on the Structure and Tribological Properties of MoSx Coating

MoSx coatings were prepared by bipolar-pulse DC unbalanced magnetron-sputtering system with the variation of coating thickness at different Ar pressures.The composition and surface morphology were determined by using energy dispersive X-ray and scanning electron microscopy;the structural characterization was analyzed by X-ray diffraction.The friction and wear properties were investigated by fretting tests in air with less than 10% and 50% relative humidity.At 0.40 Pa pressure,(002) basal plane orientation was formed throughout the coatings.At 0.88 Pa and 1.60 Pa pressures,(002) basal plane orientation was only noticed in the first stage of coating growth(around 0.20 μm in thickness), and then edge orientations with their basal planes perpendicular to the surface would be evolved in the coatings.Humidity has a minor influence on the coatings that have(002) basal plane orientation,whereas the tribological properties of MoSx coatings with edge orientations are greatly affected by humidity.The mechanisms of coating growth and friction and wear processes are discussed.     

Synthesis and electrochemical properties of layered Li[Ni0.333Co0.333Mn0.293Al0.04]O2−zFz cathode materials prepared by the sol–gel method

The cathode-active materials, layered Li[Ni_0.333Co_0.333Mn_0.293Al_0.04]O_2−zF_z (0 ≤ z ≤ 0.1), were synthesized from a sol–gel precursor at 900 °C in air. The influence of Al–F co-substitution on the structural and electrochemical properties of the as-prepared samples was characterized by X-ray diffraction (XRD), scanning electron microscope (SEM) and electrochemical experiments. The results showed that Li[Ni_0.333Co_0.333Mn_0.293Al_0.04]O_2−zF_z has a typical hexagonal structure with a single phase, the particle sizes of the samples tended to increase with increasing fluorine content. It has been found that Li[Ni_0.333Co_0.333Mn_0.293Al_0.04]O_1.95F_0.05 showed an improved cathodic behavior and discharge capacity retention compared to the undoped samples in the voltage range of 3.0–4.3 V. The electrodes prepared from Li[Ni_0.333Co_0.333Mn_0.293Al_0.04]O_1.95F_0.05 delivered an initial discharge capacity of 158 mAh⁻¹ g and an initial coulombic efficiency is 91.3%, and the capacity retention at the 20th cycle was 94.9%. Though the F-doped samples had lower initial capacities, they showed better cycle performances compared with F-free samples. Therefore, this is a promising material for a lithium-ion battery.